Would it work if I pass the board object as an parameter? - parameter board

 2024-10-15 20:21:48

Please Cut and Return to M K Martin Enterprise IncFold And Tape hereDo not tape all edges or use staplesLipat disiniPostagEstampM K Martin Enterprise Inc3950 Steﬄ er RdElmira ON CA N3B 2Z3keselamatanTake Note! This safety symbol is found throughout this manual to call your attention to instructions involving yourself and others working around the machine.Failure to follow these instructions can result in injury or death Simbol ini artinya–Attention!–Become Alert!–Your Safety is involved!Signal words are used in this manual.Peringatan: Indicates a potentially hazardous situation that may result injury.Peringatan: Indicates a potentially hazardous situation that could result in serious injury or death.Bahaya: Indicates a hazardous situation that needs to be avoided. It is you the operator that needs to be aware of these dangers.If you have any questions not answered in this manual, please contact your dealer orM K Martin Enterprise Inc.3950 Steﬄ er Rd Elmira On Ca N3B 2Z3Tel: 519-664-2752+1 855 664Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.ca Safety — It’s in your interest!Baca dan pahami Buku Panduan Operator dan semua rambu keselamatan sebelum mengoperasikan, menyervis, menyetel, memperbaiki, atau mencabut kabel.Jangan izinkan pengendara.Install and secure all guards and shields before operating the equipment.Keep hands, feet, hair and clothing away from all moving parts.Place all controls in neutral, stop tractor engine, set park brake, remove ignition key and wait for all moving parts to stop before servicing, adjusting, repairing or unplugging the mower.Place all tractor controls in neutral before starting.Never operate the mower unless you are sitting on the tractor seat.Do not operate the tractor inside a building unless there is adequate ventilation.Clear the area of bystanders, especially small children before starting.Stay clear of the machine when engaging the PTO. Keep others away.Clean reﬂ ectors, SMV sign and lights if used, before transporting.When transporting use hazard ﬂ ashing lights.Do not put hands or feet under machine while tractor engine is running.Do not operate the mower in a raised position. Objects can be thrown out from the mower with suﬃ cient force to severely injure people or pets. Stay away from mower when it is running, keep others away.Remove all sticks, stones and other loose matter in the area before starting.Review operator’s manual annually. It is the responsibility of the owner or operator to read this manual and to train all other operators before they start working with the mower. Follow all safety instructions. Safety is everyones business. By following recommended procedures, a safe working environment is provided for the operator, bystanders and the area around the work-site. Untrained operators are not qualiﬁ ed to operate the mower!Informasi PerakitanThese Finish Mowers are shipped with the “A” Frame disassembled.Assemble by undoing the top “A” Frame bolt and inserting the Brace Bars as shown above.After tightening the nut on the bolt, back the nut oﬀ 1/3-1/2 turn to allow some movement in the linkage.Ensure the Anti-Scalp roller turns free, a few drops of oil my be added on the axle shaft at this time.Ensure the wheels and the caster pivot turn freely. Lightly grease the caster pivot. When attaching Mower to tractor ensure drive-line is the right length and does not bind. (See page 22 for directions)Lokasi Stiker6 – Part # PULSAR – x22 – Part #MKlogomadeincanada8 – Serial Plate1 – Part # 224DANGER. Sharp objects could be thrown. Keep safe distance from the machine4 – Part # 211 – x2Risk of injuries. Do notremove the protective shields from the belts unless all movingparts of the machine have reached a complete standstill.3 – Part # 227Danger of dropping. Do not climb on to the machine.5 – Part # A75 – x2DANGER of possible shearing of limbs. Keep a safe distance from the machine while it is working.Data teknisPulsar 48 rearPotong LebarHP# Blades RPM Berat (lbs.)MOD.4814-203540365Pulsar 60 rear6014-223540425Pulsar 72 rear7218-253540520Pulsar 90 rear9030-405540680Tingkat KebisinganNo- load noise detectionLevel of acoustic pressure LpA dB – – – – 94 dBLevel of acoustic power LwA dB – – – – 103 dB7 – Part # F9Before operating machine, carefully read the instruction manual10 – Part # 207DANGER of being crushed.Do not get between the tractorand the machine.12 – Part # 220DANGER of being caught by the PTO shaft. Do not go near the rotating members of the machine while in operation.9 – Part # NoiseLoud noise. Wear adequate hearing protection, e.g. headphones.11 – Part # 226Before any operation of maintenance a/o ad- justment, stop, brake the tractor on level ground, lower the machine to the ground and read the instruction manual.13 – Part # 540Operate with PTO at 540 RPMOperasiFor the new operatorThis ﬁ nish Mower is designed to cut a variety of grasses. The mower will work best on dry grass.When cutting damp or long grass, use slower travel speed and you my need to frequently clean the underside of the mower deck. Power to the blades is provided by the tractor through a PTOShaft, Gearbox and Belts.This mower is designed for a 540 RPM PTO speed and will give the best performance at this speed.Many features in this mower are the result of suggestions made by customers like you.By following the operating instructions in conjunction with a good maintenance program, your Pulsar Finish Mower will provide you with many years of service.MengoperasikanAttach the mower to the tractor 3ph. Ensure the deck is level to the ground by adjusting the right hitch arm adjustment and the top link until the deck is level.Cutting height is controlled with spacers on the caster pivot. Move spacers from top to bottom of wheel beam or bottom to top as needed for the proper cutting height.Starting the MowerWith the mower slightly raised from the ground. (wheels may be oﬀ the ground 3-6 inches) Run the engine at a slow speed and slowly engage the PTO.Slowly bring the engine to PTO speed. Do not exceed rated speed.Lower the mower to the ground and proceed to mow.Kecepatan GerakTravel speed can vary between 1 and 4 mph (1.5 and 6km/h) depending on the grass and ter- rain conditions. It is the responsibility of the operator to note the conditions of the job being done and to set the speed to obtain a quality cutting job while maintaining control of the equipment. The speed can be increased for lighter cutting conditions. Decrease your speed if the cut is ragged and uneven, or uncut patches.Transport on Road – Be Safe, Be Seen!When driving on the road please follow all regulations. Use lights, reﬂ ectors, SMV sign as required by law.Wheel HeightWhen setting the height of the deck, follow this procedure:Clear the area of bystanders, especially children.Raise the 3 point hitch or lift with a hoist until the wheels are far enough oﬀ the ground to remove the casters.Stop the engine, set the park brake, remove the ignition key and wait for all moving parts to stop before dismounting.Place a large block or safety stands under the deck to support the mower.Remove the lynch pin on the caster shaft and lower the caster until it is out of it’s socket.Rearrange the spacers above and below the wheel beam for your desired deck height. Arrange all spacers equally on all 4 casters.Ensure all lynch pins are secure.Remove the blocks or safety stands.Kiat Pengoperasian:Although it is best to cut when it is dry, the Mower will work in wet conditions as well. The operator will have to travel slower for the same quality of cut. It will also be necessary to clean the bottom of the deck more frequently to prevent caking or clogging of the blade area.Cutting should always be done at the rated PTO speed of 540 RPM. The cutting action is generated at the blade tips. When the speed drops below a certain point the blade will start to tear the material rather than cut it. It will look uneven and ragged.Change gears to vary the ground speed. For your safety do not travel faster then 4 MPH (6 km/h). It is the operator’s responsibility to operate the machine in a safe manner at all times.If the grass is tall, cut it twice to obtain the best results. This allows the unit to cut less material on each pass.When mowing a new area for the ﬁ rst time, you may want to set the deck height higher to clear any objects that may be hidden in long grass. When you are familiar with the area and have not detected any foreign objects the mower height can be set to the preferred cutting height.Never cut grasses shorter than recommended for your weather conditions. Short grass is less able to withstand hot and dry conditions. It is better to cut more frequently at a longer length than cutting too short.The blades need sharpening when the grass is not cut evenly and appears to ripped oﬀ rather than a clean cut.Reduce ground speed when mowing in close quarters and around obstructions.The mower should always be operated with all 4 wheels on the ground. The mower may be lifted a few inches oﬀ the ground when maneuvering around corners or objects.The mower has three blades that turn at a high rate of speed and can expel objects out of the discharge area, 50 ft or more. It is important that the operator is aware of this and never points the mower discharge towards people, animals or property. It is etter to stop cutting when people are in the area, especially children.Sign Oﬀ FormM K Martin Enterprise Inc. follows the general Safety Standards speciﬁ ed by the American Society of Agricultural Engineers (ASAE) and the Occupational Health and Safety Administration (OSHA). Anyone who will be operating and/or maintaining the equipment must read and clearly understand ALL Safety Operating and Maintenance instructions presented in this manual. Do not operate or allow anyone else to operate this equipment until such information has been reviewed. Setiap tahun kembaliview this information before the season start-up. Make these reviews of SAFETY and OPERATION annually as a standard practice for all your equipment. We feel that an untrained operator is unqualiﬁ ed to operate this machine. A sign-oﬀ sheet is provided for your record keeping to show that all personnel who will be working with the equipment have read and understood the information in the operator’s manual and have been instructed in the operation of the equipment.Tanggal Employees Signature Employers Signature 48 – 72 Pulsar Finish Mower PartsItem #bagian #DeskripsiJumlah 48Jumlah 60Jumlah 72153537Jarak pendek888253536Spacer panjang8883OL3/16 Lynch pin444453245Garpu roda4445OLBolt 1/2 x 4 1/2 c/w In444653337Spacer roda888753670Roda444817600448 Blades317600960 Blades390000772 Blades3910118Heavy washer33310OLBolt 5/8 x 1 c/w lw33311OLBolt 3/8 x 1 1/4 c/w Iw,n121212121400-100Bunyi dering3331321397Short keystock22214900001Poros3331521399Scalp roller axle1111653671Scalp roller end2221710304Scalp roller body11118OLCotter pin 1/8 x 111119OLBolt 3/8 x 1 c/w fw,In2222053267Braket rol111212290000848 Outside spindle pulley290001060 Outside spindle pulley290000472 Outside spindle pulley223Sabuk5848 Sabuk2Be1t6860 Sabuk2Sabuk7872 Sabuk22490000948 Center spindle pulley190001160 Center spindle pulley190000372 Center spindle pulley12521395Long keystock22226900002Gearbox pulley11127OL1 1/4 Flatwasher1112853260Gearbox mount11129DJA7011Tabung manual11130OLBolt 1/4 x 1 self drilling screw222315325248 Right belt cover15329260 Right belt cover15355972 Right belt cover132OLBolt 5/16 x 3/4 c/w lw22234DJA69351PTO shield11135LF205J808gearbox11136OL5/8 Nut c/w lw4443753267Gearbox slider11138OLBolt 3/8 x 1 c/w lw,fw,n10101039OLBolt 1/2 x 3 Full thread c/w In11140OLBolt 5/16 x 3/4 c/w lw444415325248 Left belt cover15329160 Left belt cover15355872 Left belt cover142OLBolt 5/8 x 6 c/w In1114353314Top link stop1114453236Top link1114553237Top link bushing1114653234Sebuah bingkai222475323548 A frame brace bar25329060 A frame brace bar25355772 A frame brace bar24853264Stop washer22249OLBolt 3/4 x 2 1/4 c/w In22250OLBolt 3/4 x 2 c/w In2225121401Pengatur jarak2225253232Hitch link44453OLBolt 3/4 x 2 1/4 c/w In2225453061Hitch pin c/w lw,n2225553243Rear grass deflector 48153293Rear grass deflector 60154167Rear grass deflector 72156OLBolt 3/8 x 1 Gr5 Hex Bolt Zinc44457OLBolt 1/2 x 3 c/w lw.fw444583673148 Wheel beam23672760 – 72 Wheel beam22NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – Nut90 Pulsar Finishing Mower PartsItem #bagian #DescritptionQty1OLBolt 3/8 x 1 c/w lw, n52OL3/16″ Lynch Pin43OLBolt 1/2 x 3 c/w fw, lw4453537Spacer Pendek8553536Spacer Panjang86OL1/4 – 28 Grease Fitting473672790 Wheel Beam2853245Wheel Fork49OLBolt 1/2 x 4 1/2 c/w In41053670Roda41153337Spacer Roda812mkfm900001Poros513OLBolt 3/8 x 1 1/4 c/w lw, n2014walfm90000590″ Blades51510118Heavy Washer516OLBolt 5/8 x 1 c/w In51753061Hitch Pin c/w lw, n218OLBolt 3/4 x 2 c/w In21953232Hitch Link42021401Pengatur jarak221OL1/8 x 1 Cotter Pin32221400Complete Scalp Roller323OLBolt 3/8 x 1 c/w lw, fw, In62421399Scalp Roller Axle32553267Braket Rol326OL5/16 x 3/4 c/w lw2273617090 Penutup Sabuk Kiri12853229Gearbox Slider129mkfm900002Katrol Gearbox130DJA70111Manual Tube1313617390 Penutup Sabuk Kanan132DJA69351Perisai PTO133cnxLF205J808LF 205 Gearbox134OL5/8 Nut c/w lw435OL5/16 x 3/4 c/w lw43653260Pemasangan Gearbox1371400-100Cincin snap53821392Pengatur Jarak Katrol439mkfm90001090 Outside Spindle Pulley44036188Katrol pemalas241beltB11090 Mower Belt24253314Top Link Spacer14353237Top Link Bushing14453239Tautan Atas14553557A-Frame Brace Bar246OLBolt 5/8 x 6 c/w In14753234Sebuah bingkai24853264Stop Washer249OLBolt 3/4 x 3 1/4 c/w In250mkfm90001190 Inside Spindle Pulley15136167Majelis Tubuh Utama152OL20mm External Snap Ring25336519Perisai Belakang142-72 Belt Arrangement for Pulsar Finish MowerAll of the Pulsar Finish Mowers have a similar belt arrangementCatatan:The two single V-Pulleys are identical, only one of them is upside down. For the 42-72 it does not matter which pulley is right side up. There is a spacer on the spindle that is either below or on top of the pulley. For the 90 the Idler Spindles have one that sits higher then the other, therefore making setup of the other spindes to be higher of lower on the same side the Idler Spindles are.They are held in place with a snap-ring and set screws. When tightening the belt please note after a certain tension the gearbox bracket starts to deﬂ ect and the large pulley starts to angle, causing belt misalignment. Please do not tighten beyond this point! Do not use any form of belt dressing, as this causes the belts to become glazed or the dressing stays tacky and will collect dust and debris.LF-205-808 GearboxItem #bagian #DeskripsiQty10.135.5000.00Crown Gear Z23 MS120.205.030.00Pengecoran130.135.2003.00Poros input140.125.6013.00Sayap150.125.7105.00Pengatur jarak168.0.1.00000Segel Minyak 35x62x7171.125.7100.00mesin cuci pelindung188.0.1.00000Bearing 6007 (35x62x14)198.0.1.00870Bearing 6207 (35x82x17)1108.0.1.00871Bearing 6208 (40x80x18)2118.2.2.01144Castle Nut M24x21128.3.2.00409Mesin cuci (25x44x4)1138.4.1.0093Parallel Key (10x8x30)1148.1.1.00054Baut (M10x20)4158.5.2.00030Snap Ring (80x83x2.5)1168.5.3.00955Snap Ring (SB81)1178.5.2.00648Snap Ring (62x65x3)1188.6.6.003013/8 "colokan"2198.7.1.00748Dust Lip (40x80x12)1208.7.0.00744Oil Cap (72×10)1210.205.1300.00Penutup1220.244.7500.00Shim Kit (40.3×51.5)1238.5.1.00680(Snap Ring 40×37.5×2.5)1240.248.7500.00Shim Kit (69×79.7)1250.124.71.35.00Papan nama1260.113.7500.00Shim Kit (55.4×61.7)1278.5.2.00131Snap Ring (72x75x25)1280.113.7500.00Shim Kit (55.4×61.7)12518.4.7.00516Pasak1NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

Where arePulsarlawn mowers manufactured

Bellco Glass, Inc. Glassware. Please note: We are always adding images and updating records. If you do not see an image or information that you need, please ...

Second time dome climber purchase. Mama Bear. [This review was collected as part of a promotion.] Second dome climber for our family. I built both of them by ...

Simbol ini artinya–Attention!–Become Alert!–Your Safety is involved!Signal words are used in this manual.Peringatan: Indicates a potentially hazardous situation that may result injury.Peringatan: Indicates a potentially hazardous situation that could result in serious injury or death.Bahaya: Indicates a hazardous situation that needs to be avoided. It is you the operator that needs to be aware of these dangers.If you have any questions not answered in this manual, please contact your dealer orM K Martin Enterprise Inc.3950 Steﬄ er Rd Elmira On Ca N3B 2Z3Tel: 519-664-2752+1 855 664Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.ca

Item #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

The Impulse 6000D Defibrillator Analyzer and Impulse 7000DP Defibrillator/Transcutaneous Pacer Analyzer Test Systems are rugged, portable precision test instruments that ensure proper operation and ultimate performance of critical life-support cardiac-resuscitation equipment.

Pulsar mower partsdiagram

Anniversary 100. Soft Red 2300. Tango Black Edition S 381. Grunes Kreuz. Greenstar 1900. Silverstar S300. Silverbird CH. Silver Shadow.

Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

It is the responsibility of the owner or operator to read this manual and to train all other operators before they start working with the mower. Follow all safety instructions. Safety is everyones business. By following recommended procedures, a safe working environment is provided for the operator, bystanders and the area around the work-site. Untrained operators are not qualiﬁ ed to operate the mower!

Sign Oﬀ FormM K Martin Enterprise Inc. follows the general Safety Standards speciﬁ ed by the American Society of Agricultural Engineers (ASAE) and the Occupational Health and Safety Administration (OSHA). Anyone who will be operating and/or maintaining the equipment must read and clearly understand ALL Safety Operating and Maintenance instructions presented in this manual. Do not operate or allow anyone else to operate this equipment until such information has been reviewed. Setiap tahun kembaliview this information before the season start-up. Make these reviews of SAFETY and OPERATION annually as a standard practice for all your equipment. We feel that an untrained operator is unqualiﬁ ed to operate this machine. A sign-oﬀ sheet is provided for your record keeping to show that all personnel who will be working with the equipment have read and understood the information in the operator’s manual and have been instructed in the operation of the equipment.

Take Note! This safety symbol is found throughout this manual to call your attention to instructions involving yourself and others working around the machine.

Honeywell 901AS6 HONEYWELL MICRO SWITCH ASSMY, distributed by Kempston Controls. Shipping to 240+ countries worldwide.

Shop and Buy StarTech.com Expansion Slot Rear Exhaust Cooling Fan with LP4 Connector (FANCASE) - system fan kit - FANCASE from Elara Online Ireland.

These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.

It looks like your browser does not have JavaScript enabled. Please turn on JavaScript and try again.

Pulsar mower partslist

MK Martin Enterprise Inc. shall not, in any event, be liable for any losses, damages or costs; to include proﬁ ts, travel, transportation, pick up, delivery, towing cost, tow vehicle, loss of use, whether special, incidental, consequential or otherwise, in any way. Unit or parts are returned at the customer’s expense.Include a copy of your completed Warranty Registration form with any claim as proof of warranty activation.There are no warranties, expressed or implied, other than those speciﬁ ed herein. No agent, employee or other person has any authority to vary any of the foregoing provisions.Warranty coverage is null and void unless the Warranty Registration form has been completed in full and is on ﬁ le at MK Martin Enterprise Inc.Warranty begins at the time of customer delivery and is activated upon Warranty Registration receipt at MK Martin Enterprise Inc.M K Martin Enterprise Inc3950 Steﬄ er RdElmira ON CA N3B 2Z3Purchaser’s warranty protection is valid only when this completed form or a copy of this form is on ﬁ le at M K Martin Enterprise Inc. By ﬁ lling out this form the purchaser has acknowledged delivery of equipment and owner’s / operator’s manual and has accepted the condition of the equipment.Date of delivery to purchaser ——————————————————-Type of Equipment ——————————————————————-Model # ——————————- Serial # ————————————-Retailer’s Signature Indicates

Eﬀ ective on products retailed on or after November 1, 2017Two Year Limited Consumer WarrantyFive Year Limited Consumer Warranty on Gearboxes90 Day Limited Commercial Warranty including GearboxesCommercial includes rental and industrial applications.Warranty begins at the time of customer delivery and is activated upon warranty registration receipt at MK Martin Enterprise Inc.Warranty coverage is null and void unless the Warranty Registration form has been completed in full and is on ﬁ le at MK Martin Enterprise Inc.Keep your registration copy in a safe place, it is required as proof of warranty activation.This new and unused product is warranted by MK Martin Enterprise Inc. to be free from defects in material and workmanship under normal use and regular service as described in the owner’s manual, for a consumer period of 2 years and 5 years for gearboxes,from the date of delivery, and commercial period of 90 days, including gearboxes, from the date of delivery. Warranty is limited to the replacement of parts and / or repair of the product.If issues develop within the warranty period with the product, contact the local dealer from which you purchased the unit. Only MK Martin authorized dealers may make repairs to the product or aﬀ ect the replacement of defective parts, unless otherwise approved by MK Martin. Repairs / replacement will be done at no charge within a reasonable time after the receipt of the product.Garansi ini tidak mencakup item berikut:

This product can expose you to chemicals including cobalt, which is known to the State of California to cause cancer. Click here for more information.

Pulsar mower partsmanual

Pesan * Nama Email Situs Web Simpan nama saya, email, dan websitus di browser ini untuk waktu berikutnya saya berkomentar.

Pulsarlawnmower150cc

• Impulse 7010 Defibrillator Selectable Load Accessory provides multiple loads of 25 Ω, 50 Ω, 75 Ω, 100 Ω, 125 Ω, 150 Ω, 175 Ω, and 200 Ω to comply with IEC 60601-2-4 standard (optional) • Lown, Edmark, trapezoidal, biphasic and pulsed-biphasic defibrillation technology compatibility • AED technology compatibility • First-class measurement accuracy ± 1 % of reading + 0.1 J • Intuitive user interface and backlight, easy-to-read display • Portable, rugged, easy to carry • Long-lasting, rechargeable battery • Pacer brand selections • Pacer input protected against defibrillator output (7000DP only) • 10 independent ECG outputs that provide 12 lead combinations for standardized clinical signals • Flexible heart-rate settings (1 BPM step) facilitate rate meter accuracy and alarm testing • DSP-based measurements enable future firmware and waveforms upgrade • Unique integrated posts for secure connections • Two-year extended warranty (no-cost extended warranty available after first-year calibration at any Fluke Biomedical authorized service center) • Optional Ansur test automation software to standardize testing procedures, capture waveforms and test results, and print and document test results • Designed, tested, and built to incomparable Fluke quality standards

Tingkat KebisinganNo- load noise detectionLevel of acoustic pressure LpA dB – – – – 94 dBLevel of acoustic power LwA dB – – – – 103 dB

NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – Nut90 Pulsar Finishing Mower PartsItem #bagian #DescritptionQty1OLBolt 3/8 x 1 c/w lw, n52OL3/16″ Lynch Pin43OLBolt 1/2 x 3 c/w fw, lw4453537Spacer Pendek8553536Spacer Panjang86OL1/4 – 28 Grease Fitting473672790 Wheel Beam2853245Wheel Fork49OLBolt 1/2 x 4 1/2 c/w In41053670Roda41153337Spacer Roda812mkfm900001Poros513OLBolt 3/8 x 1 1/4 c/w lw, n2014walfm90000590″ Blades51510118Heavy Washer516OLBolt 5/8 x 1 c/w In51753061Hitch Pin c/w lw, n218OLBolt 3/4 x 2 c/w In21953232Hitch Link42021401Pengatur jarak221OL1/8 x 1 Cotter Pin32221400Complete Scalp Roller323OLBolt 3/8 x 1 c/w lw, fw, In62421399Scalp Roller Axle32553267Braket Rol326OL5/16 x 3/4 c/w lw2273617090 Penutup Sabuk Kiri12853229Gearbox Slider129mkfm900002Katrol Gearbox130DJA70111Manual Tube1313617390 Penutup Sabuk Kanan132DJA69351Perisai PTO133cnxLF205J808LF 205 Gearbox134OL5/8 Nut c/w lw435OL5/16 x 3/4 c/w lw43653260Pemasangan Gearbox1371400-100Cincin snap53821392Pengatur Jarak Katrol439mkfm90001090 Outside Spindle Pulley44036188Katrol pemalas241beltB11090 Mower Belt24253314Top Link Spacer14353237Top Link Bushing14453239Tautan Atas14553557A-Frame Brace Bar246OLBolt 5/8 x 6 c/w In14753234Sebuah bingkai24853264Stop Washer249OLBolt 3/4 x 3 1/4 c/w In250mkfm90001190 Inside Spindle Pulley15136167Majelis Tubuh Utama152OL20mm External Snap Ring25336519Perisai Belakang142-72 Belt Arrangement for Pulsar Finish MowerAll of the Pulsar Finish Mowers have a similar belt arrangementCatatan:The two single V-Pulleys are identical, only one of them is upside down. For the 42-72 it does not matter which pulley is right side up. There is a spacer on the spindle that is either below or on top of the pulley. For the 90 the Idler Spindles have one that sits higher then the other, therefore making setup of the other spindes to be higher of lower on the same side the Idler Spindles are.They are held in place with a snap-ring and set screws. When tightening the belt please note after a certain tension the gearbox bracket starts to deﬂ ect and the large pulley starts to angle, causing belt misalignment. Please do not tighten beyond this point! Do not use any form of belt dressing, as this causes the belts to become glazed or the dressing stays tacky and will collect dust and debris.LF-205-808 GearboxItem #bagian #DeskripsiQty10.135.5000.00Crown Gear Z23 MS120.205.030.00Pengecoran130.135.2003.00Poros input140.125.6013.00Sayap150.125.7105.00Pengatur jarak168.0.1.00000Segel Minyak 35x62x7171.125.7100.00mesin cuci pelindung188.0.1.00000Bearing 6007 (35x62x14)198.0.1.00870Bearing 6207 (35x82x17)1108.0.1.00871Bearing 6208 (40x80x18)2118.2.2.01144Castle Nut M24x21128.3.2.00409Mesin cuci (25x44x4)1138.4.1.0093Parallel Key (10x8x30)1148.1.1.00054Baut (M10x20)4158.5.2.00030Snap Ring (80x83x2.5)1168.5.3.00955Snap Ring (SB81)1178.5.2.00648Snap Ring (62x65x3)1188.6.6.003013/8 "colokan"2198.7.1.00748Dust Lip (40x80x12)1208.7.0.00744Oil Cap (72×10)1210.205.1300.00Penutup1220.244.7500.00Shim Kit (40.3×51.5)1238.5.1.00680(Snap Ring 40×37.5×2.5)1240.248.7500.00Shim Kit (69×79.7)1250.124.71.35.00Papan nama1260.113.7500.00Shim Kit (55.4×61.7)1278.5.2.00131Snap Ring (72x75x25)1280.113.7500.00Shim Kit (55.4×61.7)12518.4.7.00516Pasak1NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

The Impulse 6000D and Impulse 7000DP test capabilities encompass the spectrum of worldwide established pulse shapes, showcase breakthrough AED technology compatibility, and outperform in accuracy and standards. Additionally, the Impulse 7000DP incorporates the tests and the extensive range of test loads and measurement algorithms needed to test external transcutaneous pacemakers.

Pulsar150cc LawnMower PartsList

Hallowell Rivetwell 4 Shelf, Dbl Rivet Boltless Shelving ... Use Hallowell® Particle Board or EZ-Deck decking (double rivet only) - sold separately.

These Finish Mowers are shipped with the “A” Frame disassembled.Assemble by undoing the top “A” Frame bolt and inserting the Brace Bars as shown above.After tightening the nut on the bolt, back the nut oﬀ 1/3-1/2 turn to allow some movement in the linkage.Ensure the Anti-Scalp roller turns free, a few drops of oil my be added on the axle shaft at this time.Ensure the wheels and the caster pivot turn freely. Lightly grease the caster pivot. When attaching Mower to tractor ensure drive-line is the right length and does not bind. (See page 22 for directions)Lokasi Stiker6 – Part # PULSAR – x22 – Part #MKlogomadeincanada8 – Serial Plate1 – Part # 224DANGER. Sharp objects could be thrown. Keep safe distance from the machine4 – Part # 211 – x2Risk of injuries. Do notremove the protective shields from the belts unless all movingparts of the machine have reached a complete standstill.3 – Part # 227Danger of dropping. Do not climb on to the machine.5 – Part # A75 – x2DANGER of possible shearing of limbs. Keep a safe distance from the machine while it is working.Data teknisPulsar 48 rearPotong LebarHP# Blades RPM Berat (lbs.)MOD.4814-203540365Pulsar 60 rear6014-223540425Pulsar 72 rear7218-253540520Pulsar 90 rear9030-405540680Tingkat KebisinganNo- load noise detectionLevel of acoustic pressure LpA dB – – – – 94 dBLevel of acoustic power LwA dB – – – – 103 dB7 – Part # F9Before operating machine, carefully read the instruction manual10 – Part # 207DANGER of being crushed.Do not get between the tractorand the machine.12 – Part # 220DANGER of being caught by the PTO shaft. Do not go near the rotating members of the machine while in operation.9 – Part # NoiseLoud noise. Wear adequate hearing protection, e.g. headphones.11 – Part # 226Before any operation of maintenance a/o ad- justment, stop, brake the tractor on level ground, lower the machine to the ground and read the instruction manual.13 – Part # 540Operate with PTO at 540 RPMOperasiFor the new operatorThis ﬁ nish Mower is designed to cut a variety of grasses. The mower will work best on dry grass.When cutting damp or long grass, use slower travel speed and you my need to frequently clean the underside of the mower deck. Power to the blades is provided by the tractor through a PTOShaft, Gearbox and Belts.This mower is designed for a 540 RPM PTO speed and will give the best performance at this speed.Many features in this mower are the result of suggestions made by customers like you.By following the operating instructions in conjunction with a good maintenance program, your Pulsar Finish Mower will provide you with many years of service.MengoperasikanAttach the mower to the tractor 3ph. Ensure the deck is level to the ground by adjusting the right hitch arm adjustment and the top link until the deck is level.Cutting height is controlled with spacers on the caster pivot. Move spacers from top to bottom of wheel beam or bottom to top as needed for the proper cutting height.Starting the MowerWith the mower slightly raised from the ground. (wheels may be oﬀ the ground 3-6 inches) Run the engine at a slow speed and slowly engage the PTO.Slowly bring the engine to PTO speed. Do not exceed rated speed.Lower the mower to the ground and proceed to mow.Kecepatan GerakTravel speed can vary between 1 and 4 mph (1.5 and 6km/h) depending on the grass and ter- rain conditions. It is the responsibility of the operator to note the conditions of the job being done and to set the speed to obtain a quality cutting job while maintaining control of the equipment. The speed can be increased for lighter cutting conditions. Decrease your speed if the cut is ragged and uneven, or uncut patches.Transport on Road – Be Safe, Be Seen!When driving on the road please follow all regulations. Use lights, reﬂ ectors, SMV sign as required by law.Wheel HeightWhen setting the height of the deck, follow this procedure:Clear the area of bystanders, especially children.Raise the 3 point hitch or lift with a hoist until the wheels are far enough oﬀ the ground to remove the casters.Stop the engine, set the park brake, remove the ignition key and wait for all moving parts to stop before dismounting.Place a large block or safety stands under the deck to support the mower.Remove the lynch pin on the caster shaft and lower the caster until it is out of it’s socket.Rearrange the spacers above and below the wheel beam for your desired deck height. Arrange all spacers equally on all 4 casters.Ensure all lynch pins are secure.Remove the blocks or safety stands.Kiat Pengoperasian:Although it is best to cut when it is dry, the Mower will work in wet conditions as well. The operator will have to travel slower for the same quality of cut. It will also be necessary to clean the bottom of the deck more frequently to prevent caking or clogging of the blade area.Cutting should always be done at the rated PTO speed of 540 RPM. The cutting action is generated at the blade tips. When the speed drops below a certain point the blade will start to tear the material rather than cut it. It will look uneven and ragged.Change gears to vary the ground speed. For your safety do not travel faster then 4 MPH (6 km/h). It is the operator’s responsibility to operate the machine in a safe manner at all times.If the grass is tall, cut it twice to obtain the best results. This allows the unit to cut less material on each pass.When mowing a new area for the ﬁ rst time, you may want to set the deck height higher to clear any objects that may be hidden in long grass. When you are familiar with the area and have not detected any foreign objects the mower height can be set to the preferred cutting height.Never cut grasses shorter than recommended for your weather conditions. Short grass is less able to withstand hot and dry conditions. It is better to cut more frequently at a longer length than cutting too short.The blades need sharpening when the grass is not cut evenly and appears to ripped oﬀ rather than a clean cut.Reduce ground speed when mowing in close quarters and around obstructions.The mower should always be operated with all 4 wheels on the ground. The mower may be lifted a few inches oﬀ the ground when maneuvering around corners or objects.The mower has three blades that turn at a high rate of speed and can expel objects out of the discharge area, 50 ft or more. It is important that the operator is aware of this and never points the mower discharge towards people, animals or property. It is etter to stop cutting when people are in the area, especially children.Sign Oﬀ FormM K Martin Enterprise Inc. follows the general Safety Standards speciﬁ ed by the American Society of Agricultural Engineers (ASAE) and the Occupational Health and Safety Administration (OSHA). Anyone who will be operating and/or maintaining the equipment must read and clearly understand ALL Safety Operating and Maintenance instructions presented in this manual. Do not operate or allow anyone else to operate this equipment until such information has been reviewed. Setiap tahun kembaliview this information before the season start-up. Make these reviews of SAFETY and OPERATION annually as a standard practice for all your equipment. We feel that an untrained operator is unqualiﬁ ed to operate this machine. A sign-oﬀ sheet is provided for your record keeping to show that all personnel who will be working with the equipment have read and understood the information in the operator’s manual and have been instructed in the operation of the equipment.Tanggal Employees Signature Employers Signature 48 – 72 Pulsar Finish Mower PartsItem #bagian #DeskripsiJumlah 48Jumlah 60Jumlah 72153537Jarak pendek888253536Spacer panjang8883OL3/16 Lynch pin444453245Garpu roda4445OLBolt 1/2 x 4 1/2 c/w In444653337Spacer roda888753670Roda444817600448 Blades317600960 Blades390000772 Blades3910118Heavy washer33310OLBolt 5/8 x 1 c/w lw33311OLBolt 3/8 x 1 1/4 c/w Iw,n121212121400-100Bunyi dering3331321397Short keystock22214900001Poros3331521399Scalp roller axle1111653671Scalp roller end2221710304Scalp roller body11118OLCotter pin 1/8 x 111119OLBolt 3/8 x 1 c/w fw,In2222053267Braket rol111212290000848 Outside spindle pulley290001060 Outside spindle pulley290000472 Outside spindle pulley223Sabuk5848 Sabuk2Be1t6860 Sabuk2Sabuk7872 Sabuk22490000948 Center spindle pulley190001160 Center spindle pulley190000372 Center spindle pulley12521395Long keystock22226900002Gearbox pulley11127OL1 1/4 Flatwasher1112853260Gearbox mount11129DJA7011Tabung manual11130OLBolt 1/4 x 1 self drilling screw222315325248 Right belt cover15329260 Right belt cover15355972 Right belt cover132OLBolt 5/16 x 3/4 c/w lw22234DJA69351PTO shield11135LF205J808gearbox11136OL5/8 Nut c/w lw4443753267Gearbox slider11138OLBolt 3/8 x 1 c/w lw,fw,n10101039OLBolt 1/2 x 3 Full thread c/w In11140OLBolt 5/16 x 3/4 c/w lw444415325248 Left belt cover15329160 Left belt cover15355872 Left belt cover142OLBolt 5/8 x 6 c/w In1114353314Top link stop1114453236Top link1114553237Top link bushing1114653234Sebuah bingkai222475323548 A frame brace bar25329060 A frame brace bar25355772 A frame brace bar24853264Stop washer22249OLBolt 3/4 x 2 1/4 c/w In22250OLBolt 3/4 x 2 c/w In2225121401Pengatur jarak2225253232Hitch link44453OLBolt 3/4 x 2 1/4 c/w In2225453061Hitch pin c/w lw,n2225553243Rear grass deflector 48153293Rear grass deflector 60154167Rear grass deflector 72156OLBolt 3/8 x 1 Gr5 Hex Bolt Zinc44457OLBolt 1/2 x 3 c/w lw.fw444583673148 Wheel beam23672760 – 72 Wheel beam22NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – Nut90 Pulsar Finishing Mower PartsItem #bagian #DescritptionQty1OLBolt 3/8 x 1 c/w lw, n52OL3/16″ Lynch Pin43OLBolt 1/2 x 3 c/w fw, lw4453537Spacer Pendek8553536Spacer Panjang86OL1/4 – 28 Grease Fitting473672790 Wheel Beam2853245Wheel Fork49OLBolt 1/2 x 4 1/2 c/w In41053670Roda41153337Spacer Roda812mkfm900001Poros513OLBolt 3/8 x 1 1/4 c/w lw, n2014walfm90000590″ Blades51510118Heavy Washer516OLBolt 5/8 x 1 c/w In51753061Hitch Pin c/w lw, n218OLBolt 3/4 x 2 c/w In21953232Hitch Link42021401Pengatur jarak221OL1/8 x 1 Cotter Pin32221400Complete Scalp Roller323OLBolt 3/8 x 1 c/w lw, fw, In62421399Scalp Roller Axle32553267Braket Rol326OL5/16 x 3/4 c/w lw2273617090 Penutup Sabuk Kiri12853229Gearbox Slider129mkfm900002Katrol Gearbox130DJA70111Manual Tube1313617390 Penutup Sabuk Kanan132DJA69351Perisai PTO133cnxLF205J808LF 205 Gearbox134OL5/8 Nut c/w lw435OL5/16 x 3/4 c/w lw43653260Pemasangan Gearbox1371400-100Cincin snap53821392Pengatur Jarak Katrol439mkfm90001090 Outside Spindle Pulley44036188Katrol pemalas241beltB11090 Mower Belt24253314Top Link Spacer14353237Top Link Bushing14453239Tautan Atas14553557A-Frame Brace Bar246OLBolt 5/8 x 6 c/w In14753234Sebuah bingkai24853264Stop Washer249OLBolt 3/4 x 3 1/4 c/w In250mkfm90001190 Inside Spindle Pulley15136167Majelis Tubuh Utama152OL20mm External Snap Ring25336519Perisai Belakang142-72 Belt Arrangement for Pulsar Finish MowerAll of the Pulsar Finish Mowers have a similar belt arrangementCatatan:The two single V-Pulleys are identical, only one of them is upside down. For the 42-72 it does not matter which pulley is right side up. There is a spacer on the spindle that is either below or on top of the pulley. For the 90 the Idler Spindles have one that sits higher then the other, therefore making setup of the other spindes to be higher of lower on the same side the Idler Spindles are.They are held in place with a snap-ring and set screws. When tightening the belt please note after a certain tension the gearbox bracket starts to deﬂ ect and the large pulley starts to angle, causing belt misalignment. Please do not tighten beyond this point! Do not use any form of belt dressing, as this causes the belts to become glazed or the dressing stays tacky and will collect dust and debris.LF-205-808 GearboxItem #bagian #DeskripsiQty10.135.5000.00Crown Gear Z23 MS120.205.030.00Pengecoran130.135.2003.00Poros input140.125.6013.00Sayap150.125.7105.00Pengatur jarak168.0.1.00000Segel Minyak 35x62x7171.125.7100.00mesin cuci pelindung188.0.1.00000Bearing 6007 (35x62x14)198.0.1.00870Bearing 6207 (35x82x17)1108.0.1.00871Bearing 6208 (40x80x18)2118.2.2.01144Castle Nut M24x21128.3.2.00409Mesin cuci (25x44x4)1138.4.1.0093Parallel Key (10x8x30)1148.1.1.00054Baut (M10x20)4158.5.2.00030Snap Ring (80x83x2.5)1168.5.3.00955Snap Ring (SB81)1178.5.2.00648Snap Ring (62x65x3)1188.6.6.003013/8 "colokan"2198.7.1.00748Dust Lip (40x80x12)1208.7.0.00744Oil Cap (72×10)1210.205.1300.00Penutup1220.244.7500.00Shim Kit (40.3×51.5)1238.5.1.00680(Snap Ring 40×37.5×2.5)1240.248.7500.00Shim Kit (69×79.7)1250.124.71.35.00Papan nama1260.113.7500.00Shim Kit (55.4×61.7)1278.5.2.00131Snap Ring (72x75x25)1280.113.7500.00Shim Kit (55.4×61.7)12518.4.7.00516Pasak1NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

Item #bagian #DeskripsiQty10.135.5000.00Crown Gear Z23 MS120.205.030.00Pengecoran130.135.2003.00Poros input140.125.6013.00Sayap150.125.7105.00Pengatur jarak168.0.1.00000Segel Minyak 35x62x7171.125.7100.00mesin cuci pelindung188.0.1.00000Bearing 6007 (35x62x14)198.0.1.00870Bearing 6207 (35x82x17)1108.0.1.00871Bearing 6208 (40x80x18)2118.2.2.01144Castle Nut M24x21128.3.2.00409Mesin cuci (25x44x4)1138.4.1.0093Parallel Key (10x8x30)1148.1.1.00054Baut (M10x20)4158.5.2.00030Snap Ring (80x83x2.5)1168.5.3.00955Snap Ring (SB81)1178.5.2.00648Snap Ring (62x65x3)1188.6.6.003013/8 "colokan"2198.7.1.00748Dust Lip (40x80x12)1208.7.0.00744Oil Cap (72×10)1210.205.1300.00Penutup1220.244.7500.00Shim Kit (40.3×51.5)1238.5.1.00680(Snap Ring 40×37.5×2.5)1240.248.7500.00Shim Kit (69×79.7)1250.124.71.35.00Papan nama1260.113.7500.00Shim Kit (55.4×61.7)1278.5.2.00131Snap Ring (72x75x25)1280.113.7500.00Shim Kit (55.4×61.7)12518.4.7.00516Pasak1NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

For the new operatorThis ﬁ nish Mower is designed to cut a variety of grasses. The mower will work best on dry grass.When cutting damp or long grass, use slower travel speed and you my need to frequently clean the underside of the mower deck. Power to the blades is provided by the tractor through a PTOShaft, Gearbox and Belts.This mower is designed for a 540 RPM PTO speed and will give the best performance at this speed.Many features in this mower are the result of suggestions made by customers like you.By following the operating instructions in conjunction with a good maintenance program, your Pulsar Finish Mower will provide you with many years of service.MengoperasikanAttach the mower to the tractor 3ph. Ensure the deck is level to the ground by adjusting the right hitch arm adjustment and the top link until the deck is level.Cutting height is controlled with spacers on the caster pivot. Move spacers from top to bottom of wheel beam or bottom to top as needed for the proper cutting height.Starting the MowerWith the mower slightly raised from the ground. (wheels may be oﬀ the ground 3-6 inches) Run the engine at a slow speed and slowly engage the PTO.Slowly bring the engine to PTO speed. Do not exceed rated speed.Lower the mower to the ground and proceed to mow.Kecepatan GerakTravel speed can vary between 1 and 4 mph (1.5 and 6km/h) depending on the grass and ter- rain conditions. It is the responsibility of the operator to note the conditions of the job being done and to set the speed to obtain a quality cutting job while maintaining control of the equipment. The speed can be increased for lighter cutting conditions. Decrease your speed if the cut is ragged and uneven, or uncut patches.Transport on Road – Be Safe, Be Seen!When driving on the road please follow all regulations. Use lights, reﬂ ectors, SMV sign as required by law.Wheel HeightWhen setting the height of the deck, follow this procedure:Clear the area of bystanders, especially children.Raise the 3 point hitch or lift with a hoist until the wheels are far enough oﬀ the ground to remove the casters.Stop the engine, set the park brake, remove the ignition key and wait for all moving parts to stop before dismounting.Place a large block or safety stands under the deck to support the mower.Remove the lynch pin on the caster shaft and lower the caster until it is out of it’s socket.Rearrange the spacers above and below the wheel beam for your desired deck height. Arrange all spacers equally on all 4 casters.Ensure all lynch pins are secure.Remove the blocks or safety stands.Kiat Pengoperasian:Although it is best to cut when it is dry, the Mower will work in wet conditions as well. The operator will have to travel slower for the same quality of cut. It will also be necessary to clean the bottom of the deck more frequently to prevent caking or clogging of the blade area.Cutting should always be done at the rated PTO speed of 540 RPM. The cutting action is generated at the blade tips. When the speed drops below a certain point the blade will start to tear the material rather than cut it. It will look uneven and ragged.Change gears to vary the ground speed. For your safety do not travel faster then 4 MPH (6 km/h). It is the operator’s responsibility to operate the machine in a safe manner at all times.If the grass is tall, cut it twice to obtain the best results. This allows the unit to cut less material on each pass.When mowing a new area for the ﬁ rst time, you may want to set the deck height higher to clear any objects that may be hidden in long grass. When you are familiar with the area and have not detected any foreign objects the mower height can be set to the preferred cutting height.Never cut grasses shorter than recommended for your weather conditions. Short grass is less able to withstand hot and dry conditions. It is better to cut more frequently at a longer length than cutting too short.The blades need sharpening when the grass is not cut evenly and appears to ripped oﬀ rather than a clean cut.Reduce ground speed when mowing in close quarters and around obstructions.The mower should always be operated with all 4 wheels on the ground. The mower may be lifted a few inches oﬀ the ground when maneuvering around corners or objects.The mower has three blades that turn at a high rate of speed and can expel objects out of the discharge area, 50 ft or more. It is important that the operator is aware of this and never points the mower discharge towards people, animals or property. It is etter to stop cutting when people are in the area, especially children.Sign Oﬀ FormM K Martin Enterprise Inc. follows the general Safety Standards speciﬁ ed by the American Society of Agricultural Engineers (ASAE) and the Occupational Health and Safety Administration (OSHA). Anyone who will be operating and/or maintaining the equipment must read and clearly understand ALL Safety Operating and Maintenance instructions presented in this manual. Do not operate or allow anyone else to operate this equipment until such information has been reviewed. Setiap tahun kembaliview this information before the season start-up. Make these reviews of SAFETY and OPERATION annually as a standard practice for all your equipment. We feel that an untrained operator is unqualiﬁ ed to operate this machine. A sign-oﬀ sheet is provided for your record keeping to show that all personnel who will be working with the equipment have read and understood the information in the operator’s manual and have been instructed in the operation of the equipment.Tanggal Employees Signature Employers Signature 48 – 72 Pulsar Finish Mower PartsItem #bagian #DeskripsiJumlah 48Jumlah 60Jumlah 72153537Jarak pendek888253536Spacer panjang8883OL3/16 Lynch pin444453245Garpu roda4445OLBolt 1/2 x 4 1/2 c/w In444653337Spacer roda888753670Roda444817600448 Blades317600960 Blades390000772 Blades3910118Heavy washer33310OLBolt 5/8 x 1 c/w lw33311OLBolt 3/8 x 1 1/4 c/w Iw,n121212121400-100Bunyi dering3331321397Short keystock22214900001Poros3331521399Scalp roller axle1111653671Scalp roller end2221710304Scalp roller body11118OLCotter pin 1/8 x 111119OLBolt 3/8 x 1 c/w fw,In2222053267Braket rol111212290000848 Outside spindle pulley290001060 Outside spindle pulley290000472 Outside spindle pulley223Sabuk5848 Sabuk2Be1t6860 Sabuk2Sabuk7872 Sabuk22490000948 Center spindle pulley190001160 Center spindle pulley190000372 Center spindle pulley12521395Long keystock22226900002Gearbox pulley11127OL1 1/4 Flatwasher1112853260Gearbox mount11129DJA7011Tabung manual11130OLBolt 1/4 x 1 self drilling screw222315325248 Right belt cover15329260 Right belt cover15355972 Right belt cover132OLBolt 5/16 x 3/4 c/w lw22234DJA69351PTO shield11135LF205J808gearbox11136OL5/8 Nut c/w lw4443753267Gearbox slider11138OLBolt 3/8 x 1 c/w lw,fw,n10101039OLBolt 1/2 x 3 Full thread c/w In11140OLBolt 5/16 x 3/4 c/w lw444415325248 Left belt cover15329160 Left belt cover15355872 Left belt cover142OLBolt 5/8 x 6 c/w In1114353314Top link stop1114453236Top link1114553237Top link bushing1114653234Sebuah bingkai222475323548 A frame brace bar25329060 A frame brace bar25355772 A frame brace bar24853264Stop washer22249OLBolt 3/4 x 2 1/4 c/w In22250OLBolt 3/4 x 2 c/w In2225121401Pengatur jarak2225253232Hitch link44453OLBolt 3/4 x 2 1/4 c/w In2225453061Hitch pin c/w lw,n2225553243Rear grass deflector 48153293Rear grass deflector 60154167Rear grass deflector 72156OLBolt 3/8 x 1 Gr5 Hex Bolt Zinc44457OLBolt 1/2 x 3 c/w lw.fw444583673148 Wheel beam23672760 – 72 Wheel beam22NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – Nut90 Pulsar Finishing Mower PartsItem #bagian #DescritptionQty1OLBolt 3/8 x 1 c/w lw, n52OL3/16″ Lynch Pin43OLBolt 1/2 x 3 c/w fw, lw4453537Spacer Pendek8553536Spacer Panjang86OL1/4 – 28 Grease Fitting473672790 Wheel Beam2853245Wheel Fork49OLBolt 1/2 x 4 1/2 c/w In41053670Roda41153337Spacer Roda812mkfm900001Poros513OLBolt 3/8 x 1 1/4 c/w lw, n2014walfm90000590″ Blades51510118Heavy Washer516OLBolt 5/8 x 1 c/w In51753061Hitch Pin c/w lw, n218OLBolt 3/4 x 2 c/w In21953232Hitch Link42021401Pengatur jarak221OL1/8 x 1 Cotter Pin32221400Complete Scalp Roller323OLBolt 3/8 x 1 c/w lw, fw, In62421399Scalp Roller Axle32553267Braket Rol326OL5/16 x 3/4 c/w lw2273617090 Penutup Sabuk Kiri12853229Gearbox Slider129mkfm900002Katrol Gearbox130DJA70111Manual Tube1313617390 Penutup Sabuk Kanan132DJA69351Perisai PTO133cnxLF205J808LF 205 Gearbox134OL5/8 Nut c/w lw435OL5/16 x 3/4 c/w lw43653260Pemasangan Gearbox1371400-100Cincin snap53821392Pengatur Jarak Katrol439mkfm90001090 Outside Spindle Pulley44036188Katrol pemalas241beltB11090 Mower Belt24253314Top Link Spacer14353237Top Link Bushing14453239Tautan Atas14553557A-Frame Brace Bar246OLBolt 5/8 x 6 c/w In14753234Sebuah bingkai24853264Stop Washer249OLBolt 3/4 x 3 1/4 c/w In250mkfm90001190 Inside Spindle Pulley15136167Majelis Tubuh Utama152OL20mm External Snap Ring25336519Perisai Belakang142-72 Belt Arrangement for Pulsar Finish MowerAll of the Pulsar Finish Mowers have a similar belt arrangementCatatan:The two single V-Pulleys are identical, only one of them is upside down. For the 42-72 it does not matter which pulley is right side up. There is a spacer on the spindle that is either below or on top of the pulley. For the 90 the Idler Spindles have one that sits higher then the other, therefore making setup of the other spindes to be higher of lower on the same side the Idler Spindles are.They are held in place with a snap-ring and set screws. When tightening the belt please note after a certain tension the gearbox bracket starts to deﬂ ect and the large pulley starts to angle, causing belt misalignment. Please do not tighten beyond this point! Do not use any form of belt dressing, as this causes the belts to become glazed or the dressing stays tacky and will collect dust and debris.LF-205-808 GearboxItem #bagian #DeskripsiQty10.135.5000.00Crown Gear Z23 MS120.205.030.00Pengecoran130.135.2003.00Poros input140.125.6013.00Sayap150.125.7105.00Pengatur jarak168.0.1.00000Segel Minyak 35x62x7171.125.7100.00mesin cuci pelindung188.0.1.00000Bearing 6007 (35x62x14)198.0.1.00870Bearing 6207 (35x82x17)1108.0.1.00871Bearing 6208 (40x80x18)2118.2.2.01144Castle Nut M24x21128.3.2.00409Mesin cuci (25x44x4)1138.4.1.0093Parallel Key (10x8x30)1148.1.1.00054Baut (M10x20)4158.5.2.00030Snap Ring (80x83x2.5)1168.5.3.00955Snap Ring (SB81)1178.5.2.00648Snap Ring (62x65x3)1188.6.6.003013/8 "colokan"2198.7.1.00748Dust Lip (40x80x12)1208.7.0.00744Oil Cap (72×10)1210.205.1300.00Penutup1220.244.7500.00Shim Kit (40.3×51.5)1238.5.1.00680(Snap Ring 40×37.5×2.5)1240.248.7500.00Shim Kit (69×79.7)1250.124.71.35.00Papan nama1260.113.7500.00Shim Kit (55.4×61.7)1278.5.2.00131Snap Ring (72x75x25)1280.113.7500.00Shim Kit (55.4×61.7)12518.4.7.00516Pasak1NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

In conjunction with an Impulse 7000DP, the Impulse 7010 Defibrillator Selectable Load Accessory provides multiple loads of 25 Ω, 50 Ω, 75 Ω, 100 Ω, 125 Ω, 150 Ω, 175 Ω, and 200 Ω for defibrillator performance testing. A standard USB interface enables computer control and data transfer, and optional Ansur PC-based automation software increases productivity by outfitting users with an easy-to-use method to standardize testing procedures and capture, print and document data.

MK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.ca

6 – Part # PULSAR – x22 – Part #MKlogomadeincanada8 – Serial Plate1 – Part # 224DANGER. Sharp objects could be thrown. Keep safe distance from the machine4 – Part # 211 – x2Risk of injuries. Do notremove the protective shields from the belts unless all movingparts of the machine have reached a complete standstill.3 – Part # 227Danger of dropping. Do not climb on to the machine.5 – Part # A75 – x2DANGER of possible shearing of limbs. Keep a safe distance from the machine while it is working.Data teknisPulsar 48 rearPotong LebarHP# Blades RPM Berat (lbs.)MOD.4814-203540365Pulsar 60 rear6014-223540425Pulsar 72 rear7218-253540520Pulsar 90 rear9030-405540680Tingkat KebisinganNo- load noise detectionLevel of acoustic pressure LpA dB – – – – 94 dBLevel of acoustic power LwA dB – – – – 103 dB7 – Part # F9Before operating machine, carefully read the instruction manual10 – Part # 207DANGER of being crushed.Do not get between the tractorand the machine.12 – Part # 220DANGER of being caught by the PTO shaft. Do not go near the rotating members of the machine while in operation.9 – Part # NoiseLoud noise. Wear adequate hearing protection, e.g. headphones.11 – Part # 226Before any operation of maintenance a/o ad- justment, stop, brake the tractor on level ground, lower the machine to the ground and read the instruction manual.13 – Part # 540Operate with PTO at 540 RPMOperasiFor the new operatorThis ﬁ nish Mower is designed to cut a variety of grasses. The mower will work best on dry grass.When cutting damp or long grass, use slower travel speed and you my need to frequently clean the underside of the mower deck. Power to the blades is provided by the tractor through a PTOShaft, Gearbox and Belts.This mower is designed for a 540 RPM PTO speed and will give the best performance at this speed.Many features in this mower are the result of suggestions made by customers like you.By following the operating instructions in conjunction with a good maintenance program, your Pulsar Finish Mower will provide you with many years of service.MengoperasikanAttach the mower to the tractor 3ph. Ensure the deck is level to the ground by adjusting the right hitch arm adjustment and the top link until the deck is level.Cutting height is controlled with spacers on the caster pivot. Move spacers from top to bottom of wheel beam or bottom to top as needed for the proper cutting height.Starting the MowerWith the mower slightly raised from the ground. (wheels may be oﬀ the ground 3-6 inches) Run the engine at a slow speed and slowly engage the PTO.Slowly bring the engine to PTO speed. Do not exceed rated speed.Lower the mower to the ground and proceed to mow.Kecepatan GerakTravel speed can vary between 1 and 4 mph (1.5 and 6km/h) depending on the grass and ter- rain conditions. It is the responsibility of the operator to note the conditions of the job being done and to set the speed to obtain a quality cutting job while maintaining control of the equipment. The speed can be increased for lighter cutting conditions. Decrease your speed if the cut is ragged and uneven, or uncut patches.Transport on Road – Be Safe, Be Seen!When driving on the road please follow all regulations. Use lights, reﬂ ectors, SMV sign as required by law.Wheel HeightWhen setting the height of the deck, follow this procedure:Clear the area of bystanders, especially children.Raise the 3 point hitch or lift with a hoist until the wheels are far enough oﬀ the ground to remove the casters.Stop the engine, set the park brake, remove the ignition key and wait for all moving parts to stop before dismounting.Place a large block or safety stands under the deck to support the mower.Remove the lynch pin on the caster shaft and lower the caster until it is out of it’s socket.Rearrange the spacers above and below the wheel beam for your desired deck height. Arrange all spacers equally on all 4 casters.Ensure all lynch pins are secure.Remove the blocks or safety stands.Kiat Pengoperasian:Although it is best to cut when it is dry, the Mower will work in wet conditions as well. The operator will have to travel slower for the same quality of cut. It will also be necessary to clean the bottom of the deck more frequently to prevent caking or clogging of the blade area.Cutting should always be done at the rated PTO speed of 540 RPM. The cutting action is generated at the blade tips. When the speed drops below a certain point the blade will start to tear the material rather than cut it. It will look uneven and ragged.Change gears to vary the ground speed. For your safety do not travel faster then 4 MPH (6 km/h). It is the operator’s responsibility to operate the machine in a safe manner at all times.If the grass is tall, cut it twice to obtain the best results. This allows the unit to cut less material on each pass.When mowing a new area for the ﬁ rst time, you may want to set the deck height higher to clear any objects that may be hidden in long grass. When you are familiar with the area and have not detected any foreign objects the mower height can be set to the preferred cutting height.Never cut grasses shorter than recommended for your weather conditions. Short grass is less able to withstand hot and dry conditions. It is better to cut more frequently at a longer length than cutting too short.The blades need sharpening when the grass is not cut evenly and appears to ripped oﬀ rather than a clean cut.Reduce ground speed when mowing in close quarters and around obstructions.The mower should always be operated with all 4 wheels on the ground. The mower may be lifted a few inches oﬀ the ground when maneuvering around corners or objects.The mower has three blades that turn at a high rate of speed and can expel objects out of the discharge area, 50 ft or more. It is important that the operator is aware of this and never points the mower discharge towards people, animals or property. It is etter to stop cutting when people are in the area, especially children.Sign Oﬀ FormM K Martin Enterprise Inc. follows the general Safety Standards speciﬁ ed by the American Society of Agricultural Engineers (ASAE) and the Occupational Health and Safety Administration (OSHA). Anyone who will be operating and/or maintaining the equipment must read and clearly understand ALL Safety Operating and Maintenance instructions presented in this manual. Do not operate or allow anyone else to operate this equipment until such information has been reviewed. Setiap tahun kembaliview this information before the season start-up. Make these reviews of SAFETY and OPERATION annually as a standard practice for all your equipment. We feel that an untrained operator is unqualiﬁ ed to operate this machine. A sign-oﬀ sheet is provided for your record keeping to show that all personnel who will be working with the equipment have read and understood the information in the operator’s manual and have been instructed in the operation of the equipment.Tanggal Employees Signature Employers Signature 48 – 72 Pulsar Finish Mower PartsItem #bagian #DeskripsiJumlah 48Jumlah 60Jumlah 72153537Jarak pendek888253536Spacer panjang8883OL3/16 Lynch pin444453245Garpu roda4445OLBolt 1/2 x 4 1/2 c/w In444653337Spacer roda888753670Roda444817600448 Blades317600960 Blades390000772 Blades3910118Heavy washer33310OLBolt 5/8 x 1 c/w lw33311OLBolt 3/8 x 1 1/4 c/w Iw,n121212121400-100Bunyi dering3331321397Short keystock22214900001Poros3331521399Scalp roller axle1111653671Scalp roller end2221710304Scalp roller body11118OLCotter pin 1/8 x 111119OLBolt 3/8 x 1 c/w fw,In2222053267Braket rol111212290000848 Outside spindle pulley290001060 Outside spindle pulley290000472 Outside spindle pulley223Sabuk5848 Sabuk2Be1t6860 Sabuk2Sabuk7872 Sabuk22490000948 Center spindle pulley190001160 Center spindle pulley190000372 Center spindle pulley12521395Long keystock22226900002Gearbox pulley11127OL1 1/4 Flatwasher1112853260Gearbox mount11129DJA7011Tabung manual11130OLBolt 1/4 x 1 self drilling screw222315325248 Right belt cover15329260 Right belt cover15355972 Right belt cover132OLBolt 5/16 x 3/4 c/w lw22234DJA69351PTO shield11135LF205J808gearbox11136OL5/8 Nut c/w lw4443753267Gearbox slider11138OLBolt 3/8 x 1 c/w lw,fw,n10101039OLBolt 1/2 x 3 Full thread c/w In11140OLBolt 5/16 x 3/4 c/w lw444415325248 Left belt cover15329160 Left belt cover15355872 Left belt cover142OLBolt 5/8 x 6 c/w In1114353314Top link stop1114453236Top link1114553237Top link bushing1114653234Sebuah bingkai222475323548 A frame brace bar25329060 A frame brace bar25355772 A frame brace bar24853264Stop washer22249OLBolt 3/4 x 2 1/4 c/w In22250OLBolt 3/4 x 2 c/w In2225121401Pengatur jarak2225253232Hitch link44453OLBolt 3/4 x 2 1/4 c/w In2225453061Hitch pin c/w lw,n2225553243Rear grass deflector 48153293Rear grass deflector 60154167Rear grass deflector 72156OLBolt 3/8 x 1 Gr5 Hex Bolt Zinc44457OLBolt 1/2 x 3 c/w lw.fw444583673148 Wheel beam23672760 – 72 Wheel beam22NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – Nut90 Pulsar Finishing Mower PartsItem #bagian #DescritptionQty1OLBolt 3/8 x 1 c/w lw, n52OL3/16″ Lynch Pin43OLBolt 1/2 x 3 c/w fw, lw4453537Spacer Pendek8553536Spacer Panjang86OL1/4 – 28 Grease Fitting473672790 Wheel Beam2853245Wheel Fork49OLBolt 1/2 x 4 1/2 c/w In41053670Roda41153337Spacer Roda812mkfm900001Poros513OLBolt 3/8 x 1 1/4 c/w lw, n2014walfm90000590″ Blades51510118Heavy Washer516OLBolt 5/8 x 1 c/w In51753061Hitch Pin c/w lw, n218OLBolt 3/4 x 2 c/w In21953232Hitch Link42021401Pengatur jarak221OL1/8 x 1 Cotter Pin32221400Complete Scalp Roller323OLBolt 3/8 x 1 c/w lw, fw, In62421399Scalp Roller Axle32553267Braket Rol326OL5/16 x 3/4 c/w lw2273617090 Penutup Sabuk Kiri12853229Gearbox Slider129mkfm900002Katrol Gearbox130DJA70111Manual Tube1313617390 Penutup Sabuk Kanan132DJA69351Perisai PTO133cnxLF205J808LF 205 Gearbox134OL5/8 Nut c/w lw435OL5/16 x 3/4 c/w lw43653260Pemasangan Gearbox1371400-100Cincin snap53821392Pengatur Jarak Katrol439mkfm90001090 Outside Spindle Pulley44036188Katrol pemalas241beltB11090 Mower Belt24253314Top Link Spacer14353237Top Link Bushing14453239Tautan Atas14553557A-Frame Brace Bar246OLBolt 5/8 x 6 c/w In14753234Sebuah bingkai24853264Stop Washer249OLBolt 3/4 x 3 1/4 c/w In250mkfm90001190 Inside Spindle Pulley15136167Majelis Tubuh Utama152OL20mm External Snap Ring25336519Perisai Belakang142-72 Belt Arrangement for Pulsar Finish MowerAll of the Pulsar Finish Mowers have a similar belt arrangementCatatan:The two single V-Pulleys are identical, only one of them is upside down. For the 42-72 it does not matter which pulley is right side up. There is a spacer on the spindle that is either below or on top of the pulley. For the 90 the Idler Spindles have one that sits higher then the other, therefore making setup of the other spindes to be higher of lower on the same side the Idler Spindles are.They are held in place with a snap-ring and set screws. When tightening the belt please note after a certain tension the gearbox bracket starts to deﬂ ect and the large pulley starts to angle, causing belt misalignment. Please do not tighten beyond this point! Do not use any form of belt dressing, as this causes the belts to become glazed or the dressing stays tacky and will collect dust and debris.LF-205-808 GearboxItem #bagian #DeskripsiQty10.135.5000.00Crown Gear Z23 MS120.205.030.00Pengecoran130.135.2003.00Poros input140.125.6013.00Sayap150.125.7105.00Pengatur jarak168.0.1.00000Segel Minyak 35x62x7171.125.7100.00mesin cuci pelindung188.0.1.00000Bearing 6007 (35x62x14)198.0.1.00870Bearing 6207 (35x82x17)1108.0.1.00871Bearing 6208 (40x80x18)2118.2.2.01144Castle Nut M24x21128.3.2.00409Mesin cuci (25x44x4)1138.4.1.0093Parallel Key (10x8x30)1148.1.1.00054Baut (M10x20)4158.5.2.00030Snap Ring (80x83x2.5)1168.5.3.00955Snap Ring (SB81)1178.5.2.00648Snap Ring (62x65x3)1188.6.6.003013/8 "colokan"2198.7.1.00748Dust Lip (40x80x12)1208.7.0.00744Oil Cap (72×10)1210.205.1300.00Penutup1220.244.7500.00Shim Kit (40.3×51.5)1238.5.1.00680(Snap Ring 40×37.5×2.5)1240.248.7500.00Shim Kit (69×79.7)1250.124.71.35.00Papan nama1260.113.7500.00Shim Kit (55.4×61.7)1278.5.2.00131Snap Ring (72x75x25)1280.113.7500.00Shim Kit (55.4×61.7)12518.4.7.00516Pasak1NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

PengecerSignature —————————————-Company ————————————–Alamat -------------Acceptance of equipment fully assembledReceived operator’s manualClearly understands conditions of warrantyReceived instructions of safe and proper operation of equipmentPembeliSignature ———————————————————–Company ———————————————————Mailing address ————————————————-City —————————————— Prov/State ——– Postal Code/Zip —————Available phone number —————————————–Warranty is valid only when it has been received by manufacturer at address abovePendaftaran GaransiPlease Cut and Return to M K Martin Enterprise IncFold And Tape hereDo not tape all edges or use staplesLipat disiniPostagEstampM K Martin Enterprise Inc3950 Steﬄ er RdElmira ON CA N3B 2Z3keselamatanTake Note! This safety symbol is found throughout this manual to call your attention to instructions involving yourself and others working around the machine.Failure to follow these instructions can result in injury or death Simbol ini artinya–Attention!–Become Alert!–Your Safety is involved!Signal words are used in this manual.Peringatan: Indicates a potentially hazardous situation that may result injury.Peringatan: Indicates a potentially hazardous situation that could result in serious injury or death.Bahaya: Indicates a hazardous situation that needs to be avoided. It is you the operator that needs to be aware of these dangers.If you have any questions not answered in this manual, please contact your dealer orM K Martin Enterprise Inc.3950 Steﬄ er Rd Elmira On Ca N3B 2Z3Tel: 519-664-2752+1 855 664Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.ca Safety — It’s in your interest!Baca dan pahami Buku Panduan Operator dan semua rambu keselamatan sebelum mengoperasikan, menyervis, menyetel, memperbaiki, atau mencabut kabel.Jangan izinkan pengendara.Install and secure all guards and shields before operating the equipment.Keep hands, feet, hair and clothing away from all moving parts.Place all controls in neutral, stop tractor engine, set park brake, remove ignition key and wait for all moving parts to stop before servicing, adjusting, repairing or unplugging the mower.Place all tractor controls in neutral before starting.Never operate the mower unless you are sitting on the tractor seat.Do not operate the tractor inside a building unless there is adequate ventilation.Clear the area of bystanders, especially small children before starting.Stay clear of the machine when engaging the PTO. Keep others away.Clean reﬂ ectors, SMV sign and lights if used, before transporting.When transporting use hazard ﬂ ashing lights.Do not put hands or feet under machine while tractor engine is running.Do not operate the mower in a raised position. Objects can be thrown out from the mower with suﬃ cient force to severely injure people or pets. Stay away from mower when it is running, keep others away.Remove all sticks, stones and other loose matter in the area before starting.Review operator’s manual annually. It is the responsibility of the owner or operator to read this manual and to train all other operators before they start working with the mower. Follow all safety instructions. Safety is everyones business. By following recommended procedures, a safe working environment is provided for the operator, bystanders and the area around the work-site. Untrained operators are not qualiﬁ ed to operate the mower!Informasi PerakitanThese Finish Mowers are shipped with the “A” Frame disassembled.Assemble by undoing the top “A” Frame bolt and inserting the Brace Bars as shown above.After tightening the nut on the bolt, back the nut oﬀ 1/3-1/2 turn to allow some movement in the linkage.Ensure the Anti-Scalp roller turns free, a few drops of oil my be added on the axle shaft at this time.Ensure the wheels and the caster pivot turn freely. Lightly grease the caster pivot. When attaching Mower to tractor ensure drive-line is the right length and does not bind. (See page 22 for directions)Lokasi Stiker6 – Part # PULSAR – x22 – Part #MKlogomadeincanada8 – Serial Plate1 – Part # 224DANGER. Sharp objects could be thrown. Keep safe distance from the machine4 – Part # 211 – x2Risk of injuries. Do notremove the protective shields from the belts unless all movingparts of the machine have reached a complete standstill.3 – Part # 227Danger of dropping. Do not climb on to the machine.5 – Part # A75 – x2DANGER of possible shearing of limbs. Keep a safe distance from the machine while it is working.Data teknisPulsar 48 rearPotong LebarHP# Blades RPM Berat (lbs.)MOD.4814-203540365Pulsar 60 rear6014-223540425Pulsar 72 rear7218-253540520Pulsar 90 rear9030-405540680Tingkat KebisinganNo- load noise detectionLevel of acoustic pressure LpA dB – – – – 94 dBLevel of acoustic power LwA dB – – – – 103 dB7 – Part # F9Before operating machine, carefully read the instruction manual10 – Part # 207DANGER of being crushed.Do not get between the tractorand the machine.12 – Part # 220DANGER of being caught by the PTO shaft. Do not go near the rotating members of the machine while in operation.9 – Part # NoiseLoud noise. Wear adequate hearing protection, e.g. headphones.11 – Part # 226Before any operation of maintenance a/o ad- justment, stop, brake the tractor on level ground, lower the machine to the ground and read the instruction manual.13 – Part # 540Operate with PTO at 540 RPMOperasiFor the new operatorThis ﬁ nish Mower is designed to cut a variety of grasses. The mower will work best on dry grass.When cutting damp or long grass, use slower travel speed and you my need to frequently clean the underside of the mower deck. Power to the blades is provided by the tractor through a PTOShaft, Gearbox and Belts.This mower is designed for a 540 RPM PTO speed and will give the best performance at this speed.Many features in this mower are the result of suggestions made by customers like you.By following the operating instructions in conjunction with a good maintenance program, your Pulsar Finish Mower will provide you with many years of service.MengoperasikanAttach the mower to the tractor 3ph. Ensure the deck is level to the ground by adjusting the right hitch arm adjustment and the top link until the deck is level.Cutting height is controlled with spacers on the caster pivot. Move spacers from top to bottom of wheel beam or bottom to top as needed for the proper cutting height.Starting the MowerWith the mower slightly raised from the ground. (wheels may be oﬀ the ground 3-6 inches) Run the engine at a slow speed and slowly engage the PTO.Slowly bring the engine to PTO speed. Do not exceed rated speed.Lower the mower to the ground and proceed to mow.Kecepatan GerakTravel speed can vary between 1 and 4 mph (1.5 and 6km/h) depending on the grass and ter- rain conditions. It is the responsibility of the operator to note the conditions of the job being done and to set the speed to obtain a quality cutting job while maintaining control of the equipment. The speed can be increased for lighter cutting conditions. Decrease your speed if the cut is ragged and uneven, or uncut patches.Transport on Road – Be Safe, Be Seen!When driving on the road please follow all regulations. Use lights, reﬂ ectors, SMV sign as required by law.Wheel HeightWhen setting the height of the deck, follow this procedure:Clear the area of bystanders, especially children.Raise the 3 point hitch or lift with a hoist until the wheels are far enough oﬀ the ground to remove the casters.Stop the engine, set the park brake, remove the ignition key and wait for all moving parts to stop before dismounting.Place a large block or safety stands under the deck to support the mower.Remove the lynch pin on the caster shaft and lower the caster until it is out of it’s socket.Rearrange the spacers above and below the wheel beam for your desired deck height. Arrange all spacers equally on all 4 casters.Ensure all lynch pins are secure.Remove the blocks or safety stands.Kiat Pengoperasian:Although it is best to cut when it is dry, the Mower will work in wet conditions as well. The operator will have to travel slower for the same quality of cut. It will also be necessary to clean the bottom of the deck more frequently to prevent caking or clogging of the blade area.Cutting should always be done at the rated PTO speed of 540 RPM. The cutting action is generated at the blade tips. When the speed drops below a certain point the blade will start to tear the material rather than cut it. It will look uneven and ragged.Change gears to vary the ground speed. For your safety do not travel faster then 4 MPH (6 km/h). It is the operator’s responsibility to operate the machine in a safe manner at all times.If the grass is tall, cut it twice to obtain the best results. This allows the unit to cut less material on each pass.When mowing a new area for the ﬁ rst time, you may want to set the deck height higher to clear any objects that may be hidden in long grass. When you are familiar with the area and have not detected any foreign objects the mower height can be set to the preferred cutting height.Never cut grasses shorter than recommended for your weather conditions. Short grass is less able to withstand hot and dry conditions. It is better to cut more frequently at a longer length than cutting too short.The blades need sharpening when the grass is not cut evenly and appears to ripped oﬀ rather than a clean cut.Reduce ground speed when mowing in close quarters and around obstructions.The mower should always be operated with all 4 wheels on the ground. The mower may be lifted a few inches oﬀ the ground when maneuvering around corners or objects.The mower has three blades that turn at a high rate of speed and can expel objects out of the discharge area, 50 ft or more. It is important that the operator is aware of this and never points the mower discharge towards people, animals or property. It is etter to stop cutting when people are in the area, especially children.Sign Oﬀ FormM K Martin Enterprise Inc. follows the general Safety Standards speciﬁ ed by the American Society of Agricultural Engineers (ASAE) and the Occupational Health and Safety Administration (OSHA). Anyone who will be operating and/or maintaining the equipment must read and clearly understand ALL Safety Operating and Maintenance instructions presented in this manual. Do not operate or allow anyone else to operate this equipment until such information has been reviewed. Setiap tahun kembaliview this information before the season start-up. Make these reviews of SAFETY and OPERATION annually as a standard practice for all your equipment. We feel that an untrained operator is unqualiﬁ ed to operate this machine. A sign-oﬀ sheet is provided for your record keeping to show that all personnel who will be working with the equipment have read and understood the information in the operator’s manual and have been instructed in the operation of the equipment.Tanggal Employees Signature Employers Signature 48 – 72 Pulsar Finish Mower PartsItem #bagian #DeskripsiJumlah 48Jumlah 60Jumlah 72153537Jarak pendek888253536Spacer panjang8883OL3/16 Lynch pin444453245Garpu roda4445OLBolt 1/2 x 4 1/2 c/w In444653337Spacer roda888753670Roda444817600448 Blades317600960 Blades390000772 Blades3910118Heavy washer33310OLBolt 5/8 x 1 c/w lw33311OLBolt 3/8 x 1 1/4 c/w Iw,n121212121400-100Bunyi dering3331321397Short keystock22214900001Poros3331521399Scalp roller axle1111653671Scalp roller end2221710304Scalp roller body11118OLCotter pin 1/8 x 111119OLBolt 3/8 x 1 c/w fw,In2222053267Braket rol111212290000848 Outside spindle pulley290001060 Outside spindle pulley290000472 Outside spindle pulley223Sabuk5848 Sabuk2Be1t6860 Sabuk2Sabuk7872 Sabuk22490000948 Center spindle pulley190001160 Center spindle pulley190000372 Center spindle pulley12521395Long keystock22226900002Gearbox pulley11127OL1 1/4 Flatwasher1112853260Gearbox mount11129DJA7011Tabung manual11130OLBolt 1/4 x 1 self drilling screw222315325248 Right belt cover15329260 Right belt cover15355972 Right belt cover132OLBolt 5/16 x 3/4 c/w lw22234DJA69351PTO shield11135LF205J808gearbox11136OL5/8 Nut c/w lw4443753267Gearbox slider11138OLBolt 3/8 x 1 c/w lw,fw,n10101039OLBolt 1/2 x 3 Full thread c/w In11140OLBolt 5/16 x 3/4 c/w lw444415325248 Left belt cover15329160 Left belt cover15355872 Left belt cover142OLBolt 5/8 x 6 c/w In1114353314Top link stop1114453236Top link1114553237Top link bushing1114653234Sebuah bingkai222475323548 A frame brace bar25329060 A frame brace bar25355772 A frame brace bar24853264Stop washer22249OLBolt 3/4 x 2 1/4 c/w In22250OLBolt 3/4 x 2 c/w In2225121401Pengatur jarak2225253232Hitch link44453OLBolt 3/4 x 2 1/4 c/w In2225453061Hitch pin c/w lw,n2225553243Rear grass deflector 48153293Rear grass deflector 60154167Rear grass deflector 72156OLBolt 3/8 x 1 Gr5 Hex Bolt Zinc44457OLBolt 1/2 x 3 c/w lw.fw444583673148 Wheel beam23672760 – 72 Wheel beam22NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – Nut90 Pulsar Finishing Mower PartsItem #bagian #DescritptionQty1OLBolt 3/8 x 1 c/w lw, n52OL3/16″ Lynch Pin43OLBolt 1/2 x 3 c/w fw, lw4453537Spacer Pendek8553536Spacer Panjang86OL1/4 – 28 Grease Fitting473672790 Wheel Beam2853245Wheel Fork49OLBolt 1/2 x 4 1/2 c/w In41053670Roda41153337Spacer Roda812mkfm900001Poros513OLBolt 3/8 x 1 1/4 c/w lw, n2014walfm90000590″ Blades51510118Heavy Washer516OLBolt 5/8 x 1 c/w In51753061Hitch Pin c/w lw, n218OLBolt 3/4 x 2 c/w In21953232Hitch Link42021401Pengatur jarak221OL1/8 x 1 Cotter Pin32221400Complete Scalp Roller323OLBolt 3/8 x 1 c/w lw, fw, In62421399Scalp Roller Axle32553267Braket Rol326OL5/16 x 3/4 c/w lw2273617090 Penutup Sabuk Kiri12853229Gearbox Slider129mkfm900002Katrol Gearbox130DJA70111Manual Tube1313617390 Penutup Sabuk Kanan132DJA69351Perisai PTO133cnxLF205J808LF 205 Gearbox134OL5/8 Nut c/w lw435OL5/16 x 3/4 c/w lw43653260Pemasangan Gearbox1371400-100Cincin snap53821392Pengatur Jarak Katrol439mkfm90001090 Outside Spindle Pulley44036188Katrol pemalas241beltB11090 Mower Belt24253314Top Link Spacer14353237Top Link Bushing14453239Tautan Atas14553557A-Frame Brace Bar246OLBolt 5/8 x 6 c/w In14753234Sebuah bingkai24853264Stop Washer249OLBolt 3/4 x 3 1/4 c/w In250mkfm90001190 Inside Spindle Pulley15136167Majelis Tubuh Utama152OL20mm External Snap Ring25336519Perisai Belakang142-72 Belt Arrangement for Pulsar Finish MowerAll of the Pulsar Finish Mowers have a similar belt arrangementCatatan:The two single V-Pulleys are identical, only one of them is upside down. For the 42-72 it does not matter which pulley is right side up. There is a spacer on the spindle that is either below or on top of the pulley. For the 90 the Idler Spindles have one that sits higher then the other, therefore making setup of the other spindes to be higher of lower on the same side the Idler Spindles are.They are held in place with a snap-ring and set screws. When tightening the belt please note after a certain tension the gearbox bracket starts to deﬂ ect and the large pulley starts to angle, causing belt misalignment. Please do not tighten beyond this point! Do not use any form of belt dressing, as this causes the belts to become glazed or the dressing stays tacky and will collect dust and debris.LF-205-808 GearboxItem #bagian #DeskripsiQty10.135.5000.00Crown Gear Z23 MS120.205.030.00Pengecoran130.135.2003.00Poros input140.125.6013.00Sayap150.125.7105.00Pengatur jarak168.0.1.00000Segel Minyak 35x62x7171.125.7100.00mesin cuci pelindung188.0.1.00000Bearing 6007 (35x62x14)198.0.1.00870Bearing 6207 (35x82x17)1108.0.1.00871Bearing 6208 (40x80x18)2118.2.2.01144Castle Nut M24x21128.3.2.00409Mesin cuci (25x44x4)1138.4.1.0093Parallel Key (10x8x30)1148.1.1.00054Baut (M10x20)4158.5.2.00030Snap Ring (80x83x2.5)1168.5.3.00955Snap Ring (SB81)1178.5.2.00648Snap Ring (62x65x3)1188.6.6.003013/8 "colokan"2198.7.1.00748Dust Lip (40x80x12)1208.7.0.00744Oil Cap (72×10)1210.205.1300.00Penutup1220.244.7500.00Shim Kit (40.3×51.5)1238.5.1.00680(Snap Ring 40×37.5×2.5)1240.248.7500.00Shim Kit (69×79.7)1250.124.71.35.00Papan nama1260.113.7500.00Shim Kit (55.4×61.7)1278.5.2.00131Snap Ring (72x75x25)1280.113.7500.00Shim Kit (55.4×61.7)12518.4.7.00516Pasak1NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

Alamat email Anda tidak akan dipublikasikan. Bidang yang harus diisi ditandai *Pesan * Nama Email Situs Web Simpan nama saya, email, dan websitus di browser ini untuk waktu berikutnya saya berkomentar.

RTCI – Réchauffement Thermique Cote d’Ivoire Adresse: Rue Lumière, Face à Saprolait – Zone 4C Marcory – 30 BP 836 Abidjan 30 – Cote d’Ivoire

42-72 Belt Arrangement for Pulsar Finish MowerAll of the Pulsar Finish Mowers have a similar belt arrangementCatatan:The two single V-Pulleys are identical, only one of them is upside down. For the 42-72 it does not matter which pulley is right side up. There is a spacer on the spindle that is either below or on top of the pulley. For the 90 the Idler Spindles have one that sits higher then the other, therefore making setup of the other spindes to be higher of lower on the same side the Idler Spindles are.They are held in place with a snap-ring and set screws. When tightening the belt please note after a certain tension the gearbox bracket starts to deﬂ ect and the large pulley starts to angle, causing belt misalignment. Please do not tighten beyond this point! Do not use any form of belt dressing, as this causes the belts to become glazed or the dressing stays tacky and will collect dust and debris.LF-205-808 GearboxItem #bagian #DeskripsiQty10.135.5000.00Crown Gear Z23 MS120.205.030.00Pengecoran130.135.2003.00Poros input140.125.6013.00Sayap150.125.7105.00Pengatur jarak168.0.1.00000Segel Minyak 35x62x7171.125.7100.00mesin cuci pelindung188.0.1.00000Bearing 6007 (35x62x14)198.0.1.00870Bearing 6207 (35x82x17)1108.0.1.00871Bearing 6208 (40x80x18)2118.2.2.01144Castle Nut M24x21128.3.2.00409Mesin cuci (25x44x4)1138.4.1.0093Parallel Key (10x8x30)1148.1.1.00054Baut (M10x20)4158.5.2.00030Snap Ring (80x83x2.5)1168.5.3.00955Snap Ring (SB81)1178.5.2.00648Snap Ring (62x65x3)1188.6.6.003013/8 "colokan"2198.7.1.00748Dust Lip (40x80x12)1208.7.0.00744Oil Cap (72×10)1210.205.1300.00Penutup1220.244.7500.00Shim Kit (40.3×51.5)1238.5.1.00680(Snap Ring 40×37.5×2.5)1240.248.7500.00Shim Kit (69×79.7)1250.124.71.35.00Papan nama1260.113.7500.00Shim Kit (55.4×61.7)1278.5.2.00131Snap Ring (72x75x25)1280.113.7500.00Shim Kit (55.4×61.7)12518.4.7.00516Pasak1NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

Press and hold the light button on your unconnected thermostat until its screen flashes 3 times. The thermostat WIFI network name will then appear.

Leading global industrial gases and engineering company making customers more successful and helping to sustain, decarbonize and protect our planet.

Item #bagian #DeskripsiJumlah 48Jumlah 60Jumlah 72153537Jarak pendek888253536Spacer panjang8883OL3/16 Lynch pin444453245Garpu roda4445OLBolt 1/2 x 4 1/2 c/w In444653337Spacer roda888753670Roda444817600448 Blades317600960 Blades390000772 Blades3910118Heavy washer33310OLBolt 5/8 x 1 c/w lw33311OLBolt 3/8 x 1 1/4 c/w Iw,n121212121400-100Bunyi dering3331321397Short keystock22214900001Poros3331521399Scalp roller axle1111653671Scalp roller end2221710304Scalp roller body11118OLCotter pin 1/8 x 111119OLBolt 3/8 x 1 c/w fw,In2222053267Braket rol111212290000848 Outside spindle pulley290001060 Outside spindle pulley290000472 Outside spindle pulley223Sabuk5848 Sabuk2Be1t6860 Sabuk2Sabuk7872 Sabuk22490000948 Center spindle pulley190001160 Center spindle pulley190000372 Center spindle pulley12521395Long keystock22226900002Gearbox pulley11127OL1 1/4 Flatwasher1112853260Gearbox mount11129DJA7011Tabung manual11130OLBolt 1/4 x 1 self drilling screw222315325248 Right belt cover15329260 Right belt cover15355972 Right belt cover132OLBolt 5/16 x 3/4 c/w lw22234DJA69351PTO shield11135LF205J808gearbox11136OL5/8 Nut c/w lw4443753267Gearbox slider11138OLBolt 3/8 x 1 c/w lw,fw,n10101039OLBolt 1/2 x 3 Full thread c/w In11140OLBolt 5/16 x 3/4 c/w lw444415325248 Left belt cover15329160 Left belt cover15355872 Left belt cover142OLBolt 5/8 x 6 c/w In1114353314Top link stop1114453236Top link1114553237Top link bushing1114653234Sebuah bingkai222475323548 A frame brace bar25329060 A frame brace bar25355772 A frame brace bar24853264Stop washer22249OLBolt 3/4 x 2 1/4 c/w In22250OLBolt 3/4 x 2 c/w In2225121401Pengatur jarak2225253232Hitch link44453OLBolt 3/4 x 2 1/4 c/w In2225453061Hitch pin c/w lw,n2225553243Rear grass deflector 48153293Rear grass deflector 60154167Rear grass deflector 72156OLBolt 3/8 x 1 Gr5 Hex Bolt Zinc44457OLBolt 1/2 x 3 c/w lw.fw444583673148 Wheel beam23672760 – 72 Wheel beam22NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – Nut90 Pulsar Finishing Mower PartsItem #bagian #DescritptionQty1OLBolt 3/8 x 1 c/w lw, n52OL3/16″ Lynch Pin43OLBolt 1/2 x 3 c/w fw, lw4453537Spacer Pendek8553536Spacer Panjang86OL1/4 – 28 Grease Fitting473672790 Wheel Beam2853245Wheel Fork49OLBolt 1/2 x 4 1/2 c/w In41053670Roda41153337Spacer Roda812mkfm900001Poros513OLBolt 3/8 x 1 1/4 c/w lw, n2014walfm90000590″ Blades51510118Heavy Washer516OLBolt 5/8 x 1 c/w In51753061Hitch Pin c/w lw, n218OLBolt 3/4 x 2 c/w In21953232Hitch Link42021401Pengatur jarak221OL1/8 x 1 Cotter Pin32221400Complete Scalp Roller323OLBolt 3/8 x 1 c/w lw, fw, In62421399Scalp Roller Axle32553267Braket Rol326OL5/16 x 3/4 c/w lw2273617090 Penutup Sabuk Kiri12853229Gearbox Slider129mkfm900002Katrol Gearbox130DJA70111Manual Tube1313617390 Penutup Sabuk Kanan132DJA69351Perisai PTO133cnxLF205J808LF 205 Gearbox134OL5/8 Nut c/w lw435OL5/16 x 3/4 c/w lw43653260Pemasangan Gearbox1371400-100Cincin snap53821392Pengatur Jarak Katrol439mkfm90001090 Outside Spindle Pulley44036188Katrol pemalas241beltB11090 Mower Belt24253314Top Link Spacer14353237Top Link Bushing14453239Tautan Atas14553557A-Frame Brace Bar246OLBolt 5/8 x 6 c/w In14753234Sebuah bingkai24853264Stop Washer249OLBolt 3/4 x 3 1/4 c/w In250mkfm90001190 Inside Spindle Pulley15136167Majelis Tubuh Utama152OL20mm External Snap Ring25336519Perisai Belakang142-72 Belt Arrangement for Pulsar Finish MowerAll of the Pulsar Finish Mowers have a similar belt arrangementCatatan:The two single V-Pulleys are identical, only one of them is upside down. For the 42-72 it does not matter which pulley is right side up. There is a spacer on the spindle that is either below or on top of the pulley. For the 90 the Idler Spindles have one that sits higher then the other, therefore making setup of the other spindes to be higher of lower on the same side the Idler Spindles are.They are held in place with a snap-ring and set screws. When tightening the belt please note after a certain tension the gearbox bracket starts to deﬂ ect and the large pulley starts to angle, causing belt misalignment. Please do not tighten beyond this point! Do not use any form of belt dressing, as this causes the belts to become glazed or the dressing stays tacky and will collect dust and debris.LF-205-808 GearboxItem #bagian #DeskripsiQty10.135.5000.00Crown Gear Z23 MS120.205.030.00Pengecoran130.135.2003.00Poros input140.125.6013.00Sayap150.125.7105.00Pengatur jarak168.0.1.00000Segel Minyak 35x62x7171.125.7100.00mesin cuci pelindung188.0.1.00000Bearing 6007 (35x62x14)198.0.1.00870Bearing 6207 (35x82x17)1108.0.1.00871Bearing 6208 (40x80x18)2118.2.2.01144Castle Nut M24x21128.3.2.00409Mesin cuci (25x44x4)1138.4.1.0093Parallel Key (10x8x30)1148.1.1.00054Baut (M10x20)4158.5.2.00030Snap Ring (80x83x2.5)1168.5.3.00955Snap Ring (SB81)1178.5.2.00648Snap Ring (62x65x3)1188.6.6.003013/8 "colokan"2198.7.1.00748Dust Lip (40x80x12)1208.7.0.00744Oil Cap (72×10)1210.205.1300.00Penutup1220.244.7500.00Shim Kit (40.3×51.5)1238.5.1.00680(Snap Ring 40×37.5×2.5)1240.248.7500.00Shim Kit (69×79.7)1250.124.71.35.00Papan nama1260.113.7500.00Shim Kit (55.4×61.7)1278.5.2.00131Snap Ring (72x75x25)1280.113.7500.00Shim Kit (55.4×61.7)12518.4.7.00516Pasak1NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

All of the Pulsar Finish Mowers have a similar belt arrangementCatatan:The two single V-Pulleys are identical, only one of them is upside down. For the 42-72 it does not matter which pulley is right side up. There is a spacer on the spindle that is either below or on top of the pulley. For the 90 the Idler Spindles have one that sits higher then the other, therefore making setup of the other spindes to be higher of lower on the same side the Idler Spindles are.They are held in place with a snap-ring and set screws. When tightening the belt please note after a certain tension the gearbox bracket starts to deﬂ ect and the large pulley starts to angle, causing belt misalignment. Please do not tighten beyond this point! Do not use any form of belt dressing, as this causes the belts to become glazed or the dressing stays tacky and will collect dust and debris.LF-205-808 GearboxItem #bagian #DeskripsiQty10.135.5000.00Crown Gear Z23 MS120.205.030.00Pengecoran130.135.2003.00Poros input140.125.6013.00Sayap150.125.7105.00Pengatur jarak168.0.1.00000Segel Minyak 35x62x7171.125.7100.00mesin cuci pelindung188.0.1.00000Bearing 6007 (35x62x14)198.0.1.00870Bearing 6207 (35x82x17)1108.0.1.00871Bearing 6208 (40x80x18)2118.2.2.01144Castle Nut M24x21128.3.2.00409Mesin cuci (25x44x4)1138.4.1.0093Parallel Key (10x8x30)1148.1.1.00054Baut (M10x20)4158.5.2.00030Snap Ring (80x83x2.5)1168.5.3.00955Snap Ring (SB81)1178.5.2.00648Snap Ring (62x65x3)1188.6.6.003013/8 "colokan"2198.7.1.00748Dust Lip (40x80x12)1208.7.0.00744Oil Cap (72×10)1210.205.1300.00Penutup1220.244.7500.00Shim Kit (40.3×51.5)1238.5.1.00680(Snap Ring 40×37.5×2.5)1240.248.7500.00Shim Kit (69×79.7)1250.124.71.35.00Papan nama1260.113.7500.00Shim Kit (55.4×61.7)1278.5.2.00131Snap Ring (72x75x25)1280.113.7500.00Shim Kit (55.4×61.7)12518.4.7.00516Pasak1NoteOL – Obtain Locallyc/w – Complete Withfw – Flatwasherlw – Lockwasherln – Locknutn – NutPTO Drive-line DimensionThe PTO Drive-line as supplied with the machine will need to be checked for the proper length before being put into service.To accommodate the various hitch and tractor conﬁ gurations the supplied shaft may be too long, or in some cases too short. To determine shaft length, ﬁ nd the collapsed length, raise or lower the equipment until the PTO out of the tractor is horizontal with the input shaft on the machine. Measure lock-pin groove to lock-pin groove or bolt hole on the equipment. If this is on trailed equipment then turn tractor as sharp as possible.Measure collapsed PTO shaft from lock-pin to lock-pin or bolt hole and compare it with the measurement on the tractor. The diﬀ erence of these measurements needs to be cut from Both Halves of the PTO shaft plus 1/2”.Following these guidelines will reduce the chances of damage to the equipment.Use a sharp hacksaw to cut the PTO tubeUse a ﬁ ne ﬁ le to remove any sharp edges and burrs from sawingClean oﬀ all dirt and ﬁ lings from tube , carefully test for smooth ﬁ t.Apply a light coat of grease to the outside of the small tubeReinstall the shieldsInstall on equipment and recheckThese procedures need to be done before ﬁ rst putting into operation and when attaching to a diﬀ erent tractorPTO 48-72 NAItem #bagian #DeskripsiQty1800203Yoke 1 3/8″ Z6228202Cross Journal Assy258002021Outer Tube Yoke1898700855Pin Pegas 8×55 mm1129881363100CM 100 Cardan Tube 02 E 36×3,21139881294100CM 100 Cardan Tube 02 129 x411698700850Pin Pegas 8×50 mm1178002011Inner Tube Yoke125021902C001Cone Shield Bell 01-02226025502C001Outer Bearing 02127025402C001Outer Base Cone 01-02128998052242Sekrup6290988961N B2081Outer Safety Shield Tube1300988955NB2081Inner Safety Shield Tube131025402C002Inner Base Cone 01-02132025502C002Inner Bearing 0214025000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1PTO 84-90 B4Item #bagian #DeskripsiQty1800403Yoke 1 3/8″ Z6228204Cross Journal Assy258004021Outer Tube Yoke1898700860Pin Pegas 8×60 mm11209881433100CM 100 Cardan Tube 04 43×3 M111309881364100CM 100 Cardan Tube 04 36×4.5 M111698700855Pin Pegas 8×55 mm1178004011Inner Tube Yoke125021904C001Cone Shield Bell 03-04226025504C001Outer Bearing 03-04127025404C001Outer Base Cone 03-04128998052242Sekrup6290988966NB4086Outer Safety Shield Tube1300988961 NB4086Inner Safety Shield Tube131025404C002Inner Base Cone 03-04132025504C002Inner Bearing 03-04140252000001Rantai1489872006Drive Tube Danger Label1499872003External Shield Label151986014047Complete Push Button1Torsi BautAs used on this machineBolt torque table shown below gives torque values for various bolts used.This chart is for non-lubricated threads.Replace with same strength bolt.Torque Speciﬁ cations. Torque values are identiﬁ ed by their head markings.DiameterSAE 2SAE 5SAE 8ft-lbNmft-lbNmft-lbNm1 / 46(8)8(11)12(16)5 / 1611(15)17(24)25(33)3 / 820(27)31(42)44(59)7 / 1632(43)49(67)70(95)1 / 249(66)76(105)105(145)5 / 897(130)150(205)210(285)3 / 4144(195)265(360)375(510)7 / 8165(225)430(585)605(820)1250(340)645(875)910(1230)1 1 / 8355(480)795(1080)1290(1750)1 1 / 4500(680)1120(1520)1820(2460)1 1 / 2870(1180)1950(2640)3160(4290)These torques are for reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.pemeliharaanGood maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

Good maintenance is your responsibility. Poor maintenance is an invitation for trouble.Check for missing paint and scratches, prime and paint to keep the metal from rusting.Replace any caution, warning, danger or instruction safety decal that is not readable or is missing.The servicing periods are based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes.8 Jam atau Setiap HariLubricate PTO drive-line (4 locations)Lubricate Castor Shafts (4 Locations)Periksa Ketegangan SabukJam 20Lubricate PTO drive-line (3 locations)Jam 40Check gearbox oil level. Add 80W-90 oil as required.Lubricate wheels (4 locations)Check belt condition ( cracked, frayed etc)Setiap tahunWash Machine before storingMK Martin Enterprise Inc.3950 Steﬄ er Rd Elmira, ON, Canada N3B 2Z3Telp: 519-664-2752Pulsa Gratis: 1-855-664-2752Faks: 519-664-3695E-mail: sales@mkmartin.cawww.mkmartin.caDokumen / Sumber DayaPULSAR 2023 Finish Mower [pdf] Panduan Pengguna2023 Finish Mower, 2023, Finish Mower, MowerPos terkaitPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221SPanduan Pengguna Mesin Pemotong Rumput Pulsar PTG1221S Panduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna Mesin Pemotong Rumput Honda HRN216VKAPanduan Pengguna E-MANUAL SumsungPanduan Pengguna E-MANUAL Sumsung PANDUAN PENGGUNA AMEYOAMEYO USER MANUAL - Unduh [dioptimalkan] AMEYO USER MANUAL - Unduh

News